Jump to content

Post riepilogativo segnalato da ALFONE.(Elettronica)


hurdles

Post consigliati

ok domani provo, anche se non credo sia quello il problema, visto che ho verificato i fili dal connettore dell'impianto landi, ma non possiamo escludere niente. ho sentito anche di un modo per verificare se il collegamento del cavetto e' fatto bene, con hiperterminal ponticellando rx e tx. funziona? come si fa? per il momento grazie, a presto per aggiornamenti.

 

 

SI PUoi provare.... devi poi usare hyperterminal per testarlo

 

Loop-back Test Procedure for checking your Serial ports and/or USB - Serial Converter using HyperTerminal.

These instructions are for Win XP.

1. If you have a USB - Serial Converter, plug it in. You should check Device Manager to see if it is there first. Then proceed.

2. Go to Start - Programs - Accessories - Communications - HyperTerminal. In the box that comes up, type in a name, any name, like TEST. Click OK

3. In the Connect To window, at the bottom next to Connect Using: use the drop down menu to select the serial port you want to check - ie. COM 1. Make sure your modem is not selected! All the rest of your options on this screen will go away. Click OK

4. In the Com 1 Properties window, in the Flow Control drop down, Select NONE. Click OK.

5. You will now have a blank HyperTerminal screen. Click on File - Properties. Select the Setting Tab and at the bottom click on ASCII setup. Check the box next to Echo Typed Characters Locally. Click OK and OK again.

6. Now comes the tough part. You will need to jump pin #2 to #3 on your Male Serial Connector. The best way to do this is with a short wire with small alligator clips on each end. If you are good, you can do it with a paper clip or even a metal pen like a Cross Pen. Don't jump to any other pins! (If you look at your serial connector, there are 5 pins on top and 4 pins on the bottom, pins 1 - 5 are on the top and pins 6-9 are on the bottom. The pin orientation should read left to right as follows:

1 1 2---3 4 5

6 7 8 9

Pins 2-3 jumped. The pins are usually numbered on the plastic connector core that surrounds the pins.

7. With this accomplished, possibly with the help of a friend, start typing on your keyboard. Anything, numbers or letters.

Link to comment
Share on other sites

  • Risposte 310
  • Created
  • Last Reply

Top Posters In This Topic

infatti per quello usavo la porta com4, per provare il cavetto nel pc fisso. col portatile invece uso la com1 che e' libera, ma il messaggio e' sempre quello con hyperterminal

Controlla i bit di parity e stop se corrispondono.

 

Oppure, spesso e volentieri quando uso porte seriali per collegarmi ai decoder SAT, devo DISABILITARE il controllo flusso: prova anche tu.

Link to comment
Share on other sites

Io ho seguito alla lettera le tue istruzioni...

allora ricapitoliamo:

collego il cavetto, e verifico da gestione periferiche. qui lo vede come "Prolific usb to serial bridge" COM1

bit per secondo 9600

bit di dati 8

parita' nessuna

bit di stop 1

controllo flusso nessuno

 

imposto hyperterminal connettendo a COM1 facendo coincidere i parametri sopra elencati

risultato: IMPOSSIBILE APRIRE COM1. CONTROLLARE LE IMPOSTAZIONI DELLA PORTA

Link to comment
Share on other sites

fatto, testato sia sul portatile che sul fisso, con porte com1 com3 e com5

sempre stesso risultato

TUTTI STI problemi non li ho mai avuti... i miei cavetti sono sempre andati al primo colpo.....

c'era solo da impostare com 1 e basta !!

Link to comment
Share on other sites

Partecipa alla discussione

Puoi scrivere ora e registrarti in seguito. Se hai un account, accedi ora

Guest
Rispondi a questo topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...

×
×
  • Create New...